Modelling and Development of A Frequency Modulated Field Strength Indicator

Adamu Murtala Zungeru, Mahmud Shehu Ahmed, Garba Musa Doko, Abdul-Azeez Dauda

Research output: Contribution to journalArticle

Abstract

Measuring instruments are inevitable in the world of Science and Engineering. Most often than not Field Strength Indicator (FSI) equipment are imported at a very
expensive rate giving the economic situation currently in the developing county like Malaysia. Therefore, an inexpensive and reliable method of ascertaining the desired result becomes the motivating factor, coupled with the challenge of translating theory
into concrete terms hence serving the needs of humanity. The FM Field strength meter (FSM) otherwise known as radiation tester, is a special receiver designed to measure the field strength of an electromagnetic wave (EM Wave) radiated by any transmitter transmitting in the same frequency ranges, and displaying either on a calibrated scale or LED readout. The concept of frequency tuning using resonance LC circuit is employed
to receive signals while the other sub-circuits are used to filter out the RF signals from the received signal to have only an FM signal. This FM signal is then amplified and
displayed on the LED readout. At the end of the design and development of the system,
the performance objective that is basically to detect an appropriate level of signal within the range of frequency specified for the operation of the FSI was achieved.
Original languageEnglish
Pages (from-to)192-205
JournalInternational Journal of Emerging Trends in Engineering and Development
Volume1
Issue number4
Publication statusPublished - 2014

Fingerprint

Light emitting diodes
Networks (circuits)
Electromagnetic waves
Transmitters
Tuning
Radiation
Economics

Cite this

@article{58bd26e3d315433fba7a99d54f5ad67c,
title = "Modelling and Development of A Frequency Modulated Field Strength Indicator",
abstract = "Measuring instruments are inevitable in the world of Science and Engineering. Most often than not Field Strength Indicator (FSI) equipment are imported at a veryexpensive rate giving the economic situation currently in the developing county like Malaysia. Therefore, an inexpensive and reliable method of ascertaining the desired result becomes the motivating factor, coupled with the challenge of translating theoryinto concrete terms hence serving the needs of humanity. The FM Field strength meter (FSM) otherwise known as radiation tester, is a special receiver designed to measure the field strength of an electromagnetic wave (EM Wave) radiated by any transmitter transmitting in the same frequency ranges, and displaying either on a calibrated scale or LED readout. The concept of frequency tuning using resonance LC circuit is employedto receive signals while the other sub-circuits are used to filter out the RF signals from the received signal to have only an FM signal. This FM signal is then amplified anddisplayed on the LED readout. At the end of the design and development of the system,the performance objective that is basically to detect an appropriate level of signal within the range of frequency specified for the operation of the FSI was achieved.",
author = "Zungeru, {Adamu Murtala} and Ahmed, {Mahmud Shehu} and Doko, {Garba Musa} and Abdul-Azeez Dauda",
year = "2014",
language = "English",
volume = "1",
pages = "192--205",
journal = "International Journal of Emerging Trends in Engineering and Development",
issn = "2249-6149",
number = "4",

}

Modelling and Development of A Frequency Modulated Field Strength Indicator. / Zungeru, Adamu Murtala; Ahmed, Mahmud Shehu; Doko, Garba Musa; Dauda, Abdul-Azeez.

In: International Journal of Emerging Trends in Engineering and Development, Vol. 1, No. 4, 2014, p. 192-205.

Research output: Contribution to journalArticle

TY - JOUR

T1 - Modelling and Development of A Frequency Modulated Field Strength Indicator

AU - Zungeru, Adamu Murtala

AU - Ahmed, Mahmud Shehu

AU - Doko, Garba Musa

AU - Dauda, Abdul-Azeez

PY - 2014

Y1 - 2014

N2 - Measuring instruments are inevitable in the world of Science and Engineering. Most often than not Field Strength Indicator (FSI) equipment are imported at a veryexpensive rate giving the economic situation currently in the developing county like Malaysia. Therefore, an inexpensive and reliable method of ascertaining the desired result becomes the motivating factor, coupled with the challenge of translating theoryinto concrete terms hence serving the needs of humanity. The FM Field strength meter (FSM) otherwise known as radiation tester, is a special receiver designed to measure the field strength of an electromagnetic wave (EM Wave) radiated by any transmitter transmitting in the same frequency ranges, and displaying either on a calibrated scale or LED readout. The concept of frequency tuning using resonance LC circuit is employedto receive signals while the other sub-circuits are used to filter out the RF signals from the received signal to have only an FM signal. This FM signal is then amplified anddisplayed on the LED readout. At the end of the design and development of the system,the performance objective that is basically to detect an appropriate level of signal within the range of frequency specified for the operation of the FSI was achieved.

AB - Measuring instruments are inevitable in the world of Science and Engineering. Most often than not Field Strength Indicator (FSI) equipment are imported at a veryexpensive rate giving the economic situation currently in the developing county like Malaysia. Therefore, an inexpensive and reliable method of ascertaining the desired result becomes the motivating factor, coupled with the challenge of translating theoryinto concrete terms hence serving the needs of humanity. The FM Field strength meter (FSM) otherwise known as radiation tester, is a special receiver designed to measure the field strength of an electromagnetic wave (EM Wave) radiated by any transmitter transmitting in the same frequency ranges, and displaying either on a calibrated scale or LED readout. The concept of frequency tuning using resonance LC circuit is employedto receive signals while the other sub-circuits are used to filter out the RF signals from the received signal to have only an FM signal. This FM signal is then amplified anddisplayed on the LED readout. At the end of the design and development of the system,the performance objective that is basically to detect an appropriate level of signal within the range of frequency specified for the operation of the FSI was achieved.

M3 - Article

VL - 1

SP - 192

EP - 205

JO - International Journal of Emerging Trends in Engineering and Development

JF - International Journal of Emerging Trends in Engineering and Development

SN - 2249-6149

IS - 4

ER -